Coleman Spas Hot Tub Error Codes

One of the sensors detected that the water in the hot tub is 110°F (43.3°C). DO NOT GET INTO THE WATER. Take off the spa cover to allow the water to cool down. The hot tub should automatically reset for a temp of 107°F (41.7°C). Shut the power down to the hot tub and contact the dealer or service company if the hot tub won’t reset. Manifold 2's x 2'spg x (6) 3/4'barbs. Product ID: 672-7150. May 17, 2019 Coleman Hot Tub Features. Since Coleman Lay z spa is the best of the 2 with over 1200 reviews from customers on the Amazon. We’ll dive into the details of this hot tub product. Lay-Z-Massage System. The hydromassage system is the crucial feature of Coleman Lay-Z Spa Inflatable Hot Tub that is equipped with 120 bubble jets.

This video shows how to do a thermal reset on your Lay-Z-Spa pump. It is one of the suggested steps for solving the majority of heating issues and particularly for solving EO4, EO5 and EO8 error codes. For full details please check Here are the steps: 1. Turn the pump unit on at the mains.

Press the test button once and leave it bleeping (please ensure you leave it bleeping for at least 10 seconds). Turn the pump unit off and unplug from the socket (please ensure you leave it unplugged for at least 10 seconds). Plug the pump unit back in and turn it back on.

Press the thermal reset button using a pencil or screwdriver (see Owner’s Manual for location). Once done, press the heater button. Your pump should now be working.

Coleman is a household name for its camping products, but the company also has a line of spas in its business model. Coleman spas offer green options for these luxury tubs, using technology that reduces energy use and insulation to maintain water warmth.

811 – The Maax Spas 811 hot tub is a family friendly hot tub with many seat levels including a deep sitting corner and a lounge. 781 – The Maax spas 781 hot tub is a hydrotherapy treat with a large capacity of seating levels including a lounge, coupled with a large amount of jets. 1987 Coleman Spas Owners Manual 1988-1989 Coleman Spas Owners Manual 1990 Coleman Spas Owners Manual 1991 Coleman Spas Owners Manual. Quality spa parts company offering generic spa and hot tub replacement spa parts, spa packs and spa jets.

Coleman Spas Hot Tub Error Codes Chart

Coleman Hot Tub E02 Error

Untitled Document Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. Status of the heater element is unknown. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. OH = Over heat. The spa is at a temperature above 108°. Do not use spa when temperature is flashing or the OH message is displayed.

Coleman Hot Tub Error Codes

HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational.

SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational. PSoC = Pressure switch open with circulating pump. PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump.

ToE = Time out error. Rare system error. Spa unusable. Balboa pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. OHH = Overheat.

Spa has shut down. One sensor has detected 118º Fat heater.

OHS = Overheat. Spa has shut down. One sensor has detected 110ºF.

Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = Temp sensor malfunction SnA = Spa is shut down. Sensor plugged into jack A is not working.

Snb = Spa is shut down. Sensor plugged into jack B is not working.

Mar 16, 2018 - Keygen Xforce Autocad 2012 64 Bit keygen xforce autocad 2012 64 bitAutocad 2012 x64 (64bit) (Product key and Xforce keygen) torrent. Jan 30, 2018 - Xforce Keygen Autocad 2012 64 Bit Free lenovo e4325 amd vga driver. Download AutoCAD 2012 32-bit and 64-bit CRACK ONLY torrent. X force 2012 keygen torrent.

Coleman Spas Hot Tub Parts

SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.

Could indicate a flow problem. LF = Persistent low flow problems. (Displays on the 5th occurrence of 'HFL' message with 24 hours). Heater is shut down, but other spa functions run normally. Dr = Inadequate water detected in heater.

Dry = Inadequate water detected in heater. (Displays on third occurrence of 'dr' message). Spa is shut down.

Hot

Pr = When spa is first actuated, it will go into Priming Mode. ILOC = Interlock failure - possible pump or ozone spike. (-) =Unknown water temperature. (Displays when first powered up after refill). Std = Spa operating in Standard Mode.

Ecn = Spa operating in Economy Mode. SE = Spa operating in Standard-in-Economy Mode. Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp sensor E2 = Shorted hi-limit sensor E3 = Open hi-limit sensor E4 = Shorted flow switch E7 = Improper electrical connection CTI th1/39 = On startup indicates temperature probe problem. Th2/current temperature = On startup indicates temperature probe problem. Th3/39 = On startup indicates water temperature less than 39° F.

OH = Overheating, water over 112° F. System will restart when temp. Hot = Overheating, water over 112° F. System will restart when temp. HL = High limit switch tripped. Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated. Do not enter the water.

Pressure switch is not working. SN = Non functional high temperature sensor. Heater is deactivated.

Master Spa Hot Tub Error Codes

Spas

---or-- Message

The Current Water Temperature is 'Unknown' (- - - or - -) while in Economy or Sleep Mode.
Between Filter Cycles, while in the Economy or Sleep Heating Modes, the Pump has not turned ON and the Last Water Temperature is not current. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

--F, --C, or -- Message

The Actual Water Temperature is 'Unknown' (- -).
Priming Mode has been exited and the Pump has not yet run for 1 or 2 Minutes (depending on Model) to Sample Actual Water Temperature. With the Heat Related Pump Running, wait at Least 2 Minutes for the Correct Actual Water Temperature to be displayed. This is normal operation.

Coleman Spas Hot Tub Error Codes

drY, dY, or HEATER DRY SERVICE REQD Message

Coleman spas hot tub error codes page

There is a Verified 'Dry' (drY or dY) Condition in the heater.
The 'dr' or 'HEATER MAY BE DRY WILL RETEST SHORTLY' Fault has occurred 3 times in a row without a successful Heating Cycle and Spa Functions are Disabled. There is not enough Water in the Heater to Start it. After the Problem has been Resolved, you Must Press Any Button to reset and Restart Heater Start Up. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact us on 023 9232 1719
Check for all of the following Conditions:
1. Low Water Level.
2. Blocked Suction Fitting.
3. Blocked Skimmer.
4. Dirty Filter.
5. Too Many Closed Jets.
6. Closed Slice Valve.
7. Heat Related Pump Not Running.
8. Heat Related Pump Not Primed.

Ecn or Ec Message

If the Ecn or Ec Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Economy Heating Mode.
If the Ecn or Ec Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Economy Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles.
Ecn or Ec is Alternating with Temp:
The Spa is Operating in the 'Economy' (Ecn or Ec) Heating Mode.
The Water Temperature is sampled Only during Programmed Filter Cycles. The Heater will only operate and Heat up to Set Temperature during the Filter Cycles. The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.
Ecn or Ec is ON Solid (Not Flashing): The Current Water Temperature is 'Unknown' (- - - or - -) while in Economy or Sleep Mode. Between Filter Cycles, while in the Economy or Sleep Heating Modes, the Pump has not turned ON and the Last Water Temperature is not current. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

ICE, IC, or FREEZE COND Message

A Potential Freeze Condition has been Detected, and 'Ice' (ICE) in the System is being Prevented.
44°F (6.7°C) or Lower has been detected at the Lowest Temp Sensor, or the Aux Freeze Switch has closed, and All Pumps and Blower are activated. All Pumps and Blower are ON for at least 4 Minutes After Temp is 45°F (7.2°C) or Above at the Sensors, or when the Aux Freeze Switch Opens. This is an Operational Message, Not an Error Indication. Either wait for the Potential Freeze Condition to End, or contact us on 023 9232 1719

LF or LOW FLOW Message

There is a Verified 'Low Flow' (LF) Condition in the Heater.
The 'HFL', 'HL', or 'HTR FLOW LOW' Fault has occurred 5 times in the Last 24 Hours or Less, and Heating has been disabled. There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. After the Problem has been Resolved, you Must Press Any Button to reset and Restart Heater Start Up. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact us on 023 9232 1719
Check for all of the following Conditions:
1. Low Water Level.
2. Blocked Suction Fitting.
3. Blocked Skimmer.
4. Dirty Filter.
5. Too Many Closed Jets.
6. Closed Slice Valve.
7. Heat Related Pump Not Running.
8. Heat Related Pump Not Primed.

Pr or PRIMING MODE TAKES 4 MIN Message

The Spa is Operating in 'Priming' (Pr) Mode.
The Spa has just been powered up and is in Priming Mode for 4 Minutes. Pumps and Blower can be turned ON and OFF to remove any Air from the Heater. On EL and GL Systems Only, equipped with a 'Mode' Button, the Ozone Generator can be Turned ON for15 Seconds and OFF by using the 'Mode' Button. No automatic functions will turn ON during this time, and the Heater will Not Start. This is Not an Error Message. Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.
Note: On some Early VS and GS Systems (prior to Version 23) equipped with a 'Mode' button, the Ozone Generator can be Turned ON for 15 Seconds and OFF by using the 'Mode' button.

Codes

SbY or STANDBY MODE Message

The Spa is Operating in the 'Standby' (SbY) Mode.
All Automatic Spa System Functions are disabled so that Pumps and Blower will not turn ON Automatically. This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly. Press any Button except 'Jets 1' to Exit and Return to Normal Operation.

SLP or SL Message

Coleman Spas Hot Tub Error Codes Pictures

If the SLP or SL Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Sleep Heating Mode.
If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles.
Ecn or Ec is Alternating with Temp: The Spa is Operating in the 'Economy' (Ecn or Ec) Heating Mode.
The Water Temperature is sampled Only during Programmed Filter Cycles. The Heater will only operate and Heat up to Set Temperature during the Filter Cycles. The Water Temperature will probably drop Below Set Temperature between Filter Cycles.
Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.
Ecn or Ec is ON Solid (Not Flashing):
The Current Water Temperature is 'Unknown' (- - - or - -) while in Economy or Sleep Mode.
Between Filter Cycles, while in the Economy or Sleep Heating Modes, the Pump has not
turned ON and the Last Water Temperature is not current. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

SnA, SA, or SENSOR A SERVICE REQD Message

Coleman Spas Hot Tub Error Codes 2017

'Sensor A' (SnA or SA) is Not Operating Correctly.
The Sensor Connected to the 'Sens.A' Connector on the System Board may have failed and Spa Functions are disabled. Contact us on 023 9232 1719
A Sensor Failure Message may indicate Excessively High Heater Temperatures which can scald or Burn!
If the Heater is Not Cool Enough to Safely Service, allow the Heater to Cool before Testing.

Std, St, or STANDARD Message

The Spa is Operating in the 'Standard' (Std or St) Heating Mode.
Between filter cycles, the water temperature is sampled every 30 minutes. The heater and pump will operate any time the thermostat demands heat. The water temperature is always maintained within 1°F (.5°C) of set temperature. Other heating modes are Economy, Standard in Economy, and Sleep Modes.
Note: On the Panels that Display the 'Std' or 'St' Messages, the Message will only be
displayed for a Few Seconds After the Heating Mode is changed to Standard from a different Heating Mode.